Exclusive Offer for Email Subscribers! learn more

Signup

get free shipping on any order over $30!Learn More »

FAQ Search

and/or go

My Deep Clean Premier® has no Spray

Answer:
No Spray to Floor

 

First, be sure you are using genuine BISSELL formulas in your machine.

If you have no spray at floor, check the following:

A) Check for Liquid in the clean water tank.

If there isn’t any, add 5 ounces of BISSELL formula (fill the included measuring cup twice) into the bladder and fill the remaining with hot tap water.

B) Check the tank lid and be sure it is properly attached to the bottom tank.

To attach the lid, secure the latches on the sides.  You should be able to lift the tank by the carry handle.

 

C) Make sure the tank is properly set onto the base of the unit.

1.  First, with the tank removed, make sure the knobs that secure the front nozzle are locked sideways at the 3 o’clock and 9 o’clock positions.  

2.  Then with the handle reclined set the tank on the base.  If it doesn’t sit securely, retry.  The cap & insert need to connect into the inlet on the base.

                      DCP base pic.JPG                 

D) Make sure the tank is seated properly and the gasket is in place. 

Check the bottom of the Water Tank to make sure it has a red gasket attached and facing outwards.  The collar should tighten around the insert, if not push past the gasket and tighten.

DCP instert

 

    Incorrect                                         Incorrect                                      Correct

                              

E) Make sure the machine hasn’t lost its prime.

          Turn power off and back on.  Wait one minute then press the trigger.

 

F) Is there spray thru the hose?

          If you have spray thru hose, the pump is good.  Check for spray to the floor.

         

If there is no spray thru hose, try the following:

                   ► Remove the tool on the end of the hose and see if hose will spray. If the hose sprays when the attachment isn’t connected, then the tool is clogged. Clean out the spray-tip on the tool with a clip.  The tool may require replacement.

To order the attachment, click on this link: http://www.bissell.com/parts/?sc=product&productid=26004

                   ► Stretch the hose out and give it a few light tugs to release any kinks in the internal water supply hose. 

If there still isn’t any spray to the hose, please take the machine to a BISSELL Authorized Service Center to have a technician check it.  You can locate one by clicking here:  http://www.bissell.com/service-centers/

 

*If the machine sprays through the hose proceed as follows:

G) Remove the water tank and the front nozzle.  (The spray tips are part of the nozzle assembly)

Run warm water through the small black filter inlet screen(s) on the underside of the nozzle.  (*Cleanshot® models will have 2, other machines will have one) 

Water should easily flow through to the small black spray tips.  If not, remove spray tips and soak in hot water or scrub with a toothbrush.

DCP Nozzle Removal

 

H) Re-attach the handle:

If other steps fail to fix the problem, remove the handle completely and re-attach. Once the handle is re-attached, plug your machine in and turn the power on and re-attempt to spray.

 

If your machine has no spray thru hose, but it sprays to the floor:

A) Make sure the machine hasn’t lost its prime.

          Turn power off and back on.  Wait one minute then press the trigger.

 

B) Is there spray thru the hose?

          If you have spray thru hose, the pump is good.  Check for spray to the floor.

         

If there is no spray thru hose, try the following:

                   ► Remove the tool on the end of the hose and see if hose will spray. If the hose sprays when the attachment isn’t connected, then the tool is clogged. Clean out the spray-tip   

                       on the tool with a paper clip. The tool may require replacement.  To order the attachment, click on this link: http://www.bissell.com/parts/?sc=product&productid=26004

                   ► Stretch the hose out and give it a few light tugs to release

                       any kinks in the internal water supply hose.

 

If there still isn’t any spray to the hose, please take the machine to a BISSELL Authorized Service Center to have a technician check it.

 

You can locate one by clicking here:  http://www.bissell.com/service-centers/.

 

 

Located on the white label above, usually on the back of the machine.
Close

Sign up for BISSELL Emails!

Get expert advice, time-saving tips & special offers.

New Subscriber? Sign up and receive 10% off your next bissell.com purchase!

Sign Up

It looks like that is an improperly formatted email address. Please try again.
Close

Thank You For Signing Up!

Check your inbox for expert advice, time-saving
tips & special offers.

Home to a Deeper Clean
Loading
Loading